Advantage chillers and  temperature control units
Published

PE, PS, PVC Prices Up, PP Down

The pricing trajectory has been upwards for three of the four commodity resins, though it may be slowing for two.

Share

Global and domestic tightness in feedstocks or resins and increased costs for some feedstocks continued to drive prices upwards for PE, PS, and PVC, though that ascent may be leveling off for PVC and PS. Meanwhile, PP prices dropped again last month, though the decreases are not on par with propylene monomer decreases—evidence of suppliers’ growing success in decoupling PP price from monomer tabs. Those are the views of purchasing consultants at Resin Technology, Inc. (RTi), Fort Worth, Texas, and CEO Michael Greenberg of The Plastics Exchange, Chicago.

PE PRICES UP
Polyethylene prices were moving up 5¢/lb in May, with processors losing leverage due to a burgeoning export market. North American PE suppliers have the cost advantage globally.

North American ethylene monomer prices are not an influencing factor on PE prices. Last month’s resin price hike and the potential for additional ones depend heavily on both the price of oil-based pellets made from naphtha and tight ethylene supplies in other world regions, explains Mike Burns, v.p. for PE at RTi.

Planned ethylene turnarounds in South East Asia, and China and unplanned ethylene production disruptions in Europe and the Middle East, have resulted in ethylene abroad selling at prices as high as those of PE resins, which also have been rising. In contrast, cash cost to produce North American ethylene remains below 9¢/lb, and the cost to deliver pellets is still under 30¢/lb, according to Burns. “North America’s ability to meet any price globally will be one of the suppliers’ key drivers for managing inventories and influencing pricing.”

Greenberg reports “very aggressive” spot PE trading in April, ahead of the May price increase. “This is the first price increase with any realistic shot of implementation since September 2014,” he says. Greenberg also reports that rallying spot prices erased the previous discount versus contract prices.

While PE prices appear to be rising, Burns points out that PE film processors notified customers of a 7% increase, effective in May, exceeding that month’s resin price hike and thereby enhancing margins. “This is good for the industry and eventually we will see processors of other PE goods increase their prices.”

PP PRICES DOWN
Polypropylene prices dropped an average of 4¢/lb in April, though propylene monomer contract prices dropped 6¢/lb. Suppliers evidently were able to leverage supply/demand dynamics to implement another 2¢/lb margin expansion.

May monomer contracts were expected to be flat or lower by 1-2¢/lb, and PP prices would be likely follow. However, both Greenberg and Scott Newell, RTi’s director of client services for PP, concede that if current market conditions persist, PP suppliers may aim for additional margin expansion by holding onto any drop in monomer cost. Says Newell, “Margin expansion will continue to be a ‘talking point’ for the rest of the year.”

Greenberg reports that while PP spot trading continued to improve along with material availability as planned and unplanned production disruptions were resolved, there were still shortages of some grades and spot prices at a significant premium to contract. Newell points out that while American Chemistry Council numbers show improvements in supply—with inventory building in March, there seems to be a disconnect with what is happening on the street, so to speak. “There is definitely some improvement in supply, but the feeling out there is that things are pretty tight, with copolymers in general more difficult to get.”

PS PRICES RISING
Polystyrene prices moved up 5¢/lb as suppliers implemented their March increase a month late. However, suppliers also issued May increases of 3-6 ¢/lb, which were unlikely to be felt until this month, according to Mark Kallman, RTi’s v.p. of client services for engineering resins, PS, and PVC.

Kallman ventures that 3¢/lb is more likely than a higher increase, based on benzene contract prices, which were up a total of 24¢/gal in April and May. “Benzene is now looking like a balanced market, and any additional increase will be small—about 10¢/gal,” he states. Kallman also notes that while the PS market has been tightly balanced, PS supply is improving and styrene monomer exports have slowed. Although there is the seasonal upsurge in demand for PS due to construction and recreational products, it appears to be a normal, not an extraordinary, uptick—all of which do not support a 6¢/lb increase.

PVC PRICES MAY STABILIZE
PVC prices moved up 3¢/lb as suppliers implemented their March increase. Despite the April 3¢/lb hike that was also on the table, PVC prices remained flat through April and into May. RTi’s Kallman ventures that prices for this month would be flat to lower.

There are no cost- or supply- driven issues supporting the April increase, says Kallman. PVC resin plants are all back up and running after a series of planned maintenance turnarounds; the overall ethylene supply situation is looking good; and ethylene prices are expected to continue on the low side. A resin price hike could emerge for July or August if the construction market picks up. “The construction season started later than usual to begin with, and though it is expected to be stronger than in 2014, it is not expected to be as strong as originally projected,” says Kallman.

Make Every Pellet Count
Advantage temperature control units
Create custom Smartflow assemblies on-line, 24/7.
Maguire Ultra
Dri-Air
Konica Minolta
Shuttle Mold System
Vacuum conveying powders to extruders compounding
Plastics Recycling Latam
Insert molding automation
Vecoplan
New 2024 Twin Screw Report

Related Content

resin pricing

Prices Up for PE, PP, PS, Flat for PVC, PET

Trajectory is generally flat-to-down for all commodity resins.

Read More

Fundamentals of Polyethylene – Part 6: PE Performance

Don’t assume you know everything there is to know about PE because it’s been around so long. Here is yet another example of how the performance of PE is influenced by molecular weight and density.

Read More
PVC

First Quarter Looks Mostly Flat for Resin Prices

Temporary upward blips don't indicate any sustained movement in the near term.

Read More
SPONSORED

New Entrant Heartland Polymers Stepping up as Reliable Supplier

Heartland Polymers’ new Alberta, Canada facility will produce 525 KTA propylene and 525 KTA polypropylene. It is expected to stabilize supply chains across the continent.

Read More

Read Next

Extrusion Know How

How Polymer Melts in Single-Screw Extruders

Understanding how polymer melts in a single-screw extruder could help you optimize your screw design to eliminate defect-causing solid polymer fragments.  

Read More
Extrusion

Troubleshooting Screw and Barrel Wear in Extrusion

Extruder screws and barrels will wear over time. If you are seeing a  reduction in specific rate and higher discharge temperatures, wear is the likely culprit.   

Read More
Build custom Smartflow Assemblies on your schedule