Scientific Molding/Injection Molding Solutions

1019 Balfour St.
Midland, MI 48640 US


As Seen In Plastics Technology

B&B Molders Sticks to Its Core— Core Values & Core Competencies
To compete in today’s market, you need good technology, but you also need to know what you stand for and what you’re good at.

MRPC Takes ‘Holistic’ Approach To Scientific Molding
Last year this family-owned molder made a major commitment to Scientific Molding by starting a training process involving all employees.

A New Look at Evaluating Fill Times For Injection Molding
One of the important process parameters to establish and record for any injection molded part is its injection or fill time. Research research reveals the limitations of popularly taught methods of establishing this critical parameter.

Taking the Temperature of Mold Productivity
Increasing traffic in transfer tooling from molders that have shuttered operations or are unable to successfully produce parts is driving interest in a long-established but under-utilized diagnostic technique for injection molding.

John Bozzelli of Scientific Molding -- Injection Molding Solutions

Injection Molding: How to Set Second-Stage (Pack & Hold) Pressure
Most molders work with two parameters for establishing second-stage pressure. But within Scientific Molding there are actually four.

Mold flow analysis

Injection Molding: Understanding Pressure Loss In Injection Molding
One of the more prominent trends in processing is the need for higher plastic pressures to mold parts.

Figure 1

Injection Molding: Processors: Teach Part Designers The Golden Rule
Make sure the designers you work with understand that there are limits to what processing can do.

Gate Seal Data

Injection Molding: Why & How to Do Gate-Seal Experiments
Part of optimizing any molding process is determining the second-stage injection, or pack and hold, parameters.

Injection Molding: Answers to Bozzelli's Drying Quiz
Three questions about drying plastics that everyone should know how to answer.

Injection Molding: You Must Dry Hygroscopic Resins
The reason you dry certain plastics is to get the moisture out. But why does the moisture have to be taken out before processing?

40 molding machines

On-Site: An ‘Empire’ Built on Scientific Molding
A U.S. custom injection molder that’s hiring?

Figure 1

Injection Molding: The Basics of Machine Evaluation, Part III
In the last two issues, we started defining some basic tests to ensure your injection molding machine is working properly.

Photo: Powerline Mosaic control from Milacron Inc.

How to Make the Transition to Electric Presses
Electric injection machines are becoming more and more prevalent, and as they hit the shop floor, you are responsible for making them produce parts with dimensions, appearance, and performance to client specifications.

Don't Neglect Cooling... There's Money to Be Made
For most injection molding jobs, cooling is 95% of the cycle time.

Figure 1

Balanced Filling Is Critical for Holding Molding Tolerances
Processors face a multitude of challenges whenever they approach an injection molding machine.

Good Reasons to Make a Short Shot, and How to Do It Right
Making a proper short shot is an important aspect of practicing “scientific molding.” Upon startup of almost any mold, the first step is to make a short shot.

Plastics change viscosity in response to shear

Injection Molding Know-How: The ABCs of Delta P: Setting the First-Stage Pressure Limit
Here’s another trick of the trade that will make your life easier.

Platens “wrap” around the mold

How to Solve Uneven Clamping
Of the hundreds of variables involved in injection molding, clamping mechanisms and platens often get less attention than they deserve.

Record grooves

Find the Source of Visual Defects
The appearance of visual defects on parts such as cracking, crazing, grooves, ripples, wave marks, and flaky brittleness often indicates more than an aesthetic problem.

Product Categories of Scientific Molding/Injection Molding Solutions

Consultants--Design, Manufacturing, Purchasing
R&D, Training Institutes
Training Programs in Plastics
Troubleshooting, Problem Solving Systems